Autonomous vehicles, and self-driving cars in particular, are probably one of the most enticing technologies of the 21st century. But despite a great deal of R&D and even more speculation, we have yet to see a self-driving car that can actually operate on real public roads without any human oversight at all. If, however, we […]
Autonomous vehicles, and self-driving cars in particular, are probably one of the most enticing technologies of the 21st century. But despite a great deal of R&D and even more speculation, we have yet to see a self-driving car that can actually operate on real public roads without any human oversight at all. If, however, we remove that “real public roads” constraint, the challenge becomes a lot more approachable. All you need is a few Arduino boards and a webcam, as proven by Austin Blake’s self-driving go-kart.
Blake previously attempted a miniature self-driving Tesla project, which was supposed to drive around a park walking path. That was only a partial success, because the vehicle struggled to put its “behavioral cloning” machine learning algorithms into practice. Blake took those lessons and applied them here, with much better results.
Behavioral cloning, in this context, means that the machine learning algorithm watches what Blake does as he drives around the track, then attempts to replicate that while driving on its own. During training, it looks ahead of the kart through a webcam while monitoring the steering angle. Then, while driving on its own, it looks through the webcam at the track and tries to match the steering angle to what it saw during training.
The machine learning model runs on a laptop, but Blake needed a way for it to control the kart’s steering and throttle. He used three Arduino Nano boards to pull that off. The first just listens to the machine learning model’s serial output for a PWM signal representing the steering angle. It then sends that to the second, which uses that information and the real-time steering angle to control a Cytron motor driver for the steering. The third controls the throttle using an RC car-style circuit.
This proved to work quite well and the go-kart can navigate around a small track in Blake’s workshop. In theory, it could also handle new tracks — so long as they have similar clearly marked edges.
Materials, when exposed to light, will reflect or absorb certain portions of the electromagnetic spectrum that can give valuable information about their chemical or physical compositions. Traditional setups use a single lamp to emit white light before it is split apart into a spectrum of colors via a system of prisms, mirrors, and lenses. After […]
Materials, when exposed to light, will reflect or absorb certain portions of the electromagnetic spectrum that can give valuable information about their chemical or physical compositions. Traditional setups use a single lamp to emit white light before it is split apart into a spectrum of colors via a system of prisms, mirrors, and lenses. After hitting the substance being tested, a sensor will gather this spectral color data for analysis. YouTuber Marb’s Lab realized that by leveraging several discrete. LEDs, he could recreate this array of light without the need for the more expensive/complicated optics.
His project uses the AS7431 10-channel spectrometer sensor breakout board from Adafruit due to its adequate accuracy and compact footprint. Once it was attached to the clear sample chamber and wired to a connector, Marb got to work on the electromechanical portion of the system. Here, a stepper motor rotates a ring of six LEDs that are driven by a series of N-channel MOSFETs and a decade counter. Each component was then wired into a custom-designed control board, which acts as a shield when attached to the Arduino Mega 2560 below.
The sketch running on the Mega allows for the user to select between photometer (single wavelength) and spectrometer (multiple wavelengths) modes when sampling the substance. Once the data is captured, the user can then choose one of three interpolation modes to get a smooth curve, as seen here when measuring this chlorophyl.
Lab equipment is — traditionally at least — tremendously expensive. While there are understandable reasons for those costs, they are prohibitive to anyone operating outside of a university or corporate lab. But as the “citizen science” movement has grown, we’ve seen more and more open-source and affordable designs for lab equipment hitting the internet. The […]
Lab equipment is — traditionally at least — tremendously expensive. While there are understandable reasons for those costs, they are prohibitive to anyone operating outside of a university or corporate lab. But as the “citizen science” movement has grown, we’ve seen more and more open-source and affordable designs for lab equipment hitting the internet. The latest will be interesting to anyone who wants to do work with DNA or RNA: the DIYNAFLUOR.
DINYAFLUOR stands for “DIY Nucleic Acid Fluorometer,” which describes this device’s function. A fluorometer is a piece of equipment the measures the amount of light emitted by anything that fluoresces. In this context, that would be a reagent that increases in fluorescence when it comes into contact with the nucleic acid in DNA or RNA. The more light the fluorometer detects, the more nucleic acid is present in the sample. Sensitivity is important, which is part of the reason that fluorometers are expensive (usually several thousand dollars for basic models).
The DIYNAFLUOR, on the other hand, only costs about $40 to build. It works with both custom and commercially made fluorescent DNA quantification kits and can measure DNA on the scale of nano-micrograms.
This is affordable because its designers built it around off-the-shelf components that are easy to source and a 3D-printable enclosure. The primary component is an Arduino UNO Rev3 board, which looks at the sample through a TSL2591-based light sensor. An LED puts out 470nm light to excite the reagent and optical filters remove the unwanted wavelengths. User-friendly software with a simple GUI lets citizen scientists take measurements and record data directly to their computers.
This may be a specialized device with narrow appeal. But for those who want to work with DNA or RNA outside of a “real” lab, the cost and performance of DIYNAFLUOR is unbeatable.
Managing shared spaces, especially meeting rooms, can be a headache in busy offices. At Arduino, we’ve experienced it firsthand in our flexible and dynamic offices around the world – where colleagues could often be seen wandering around with their laptops, trying to find a quiet place for videocalls or brainstorming sessions. We started with a simple […]
Managing shared spaces, especially meeting rooms, can be a headache in busy offices. At Arduino, we’ve experienced it firsthand in our flexible and dynamic offices around the world – where colleagues could often be seen wandering around with their laptops, trying to find a quiet place for videocalls or brainstorming sessions.
We started with a simple shared Google Calendar, but as we often do, we took it a step further by creating an innovative solution – using Arduino GIGA R1 WiFi and GIGA Display Shield.
Open the door to better room booking
Our engineers developed a physical device that can be conveniently installed next to every meeting room door, using the Arduino GIGA and GIGA Display Shield. The device connects seamlessly with Google Calendar APIs, allowing users to check room availability and book a space directly from the touchscreen. The APIs are managed by a custom Python® application that processes Google Calendar data and updates the corresponding IoT Thing in Arduino Cloud.
No more knocking on doors or interrupting meetings to check if the room is free! It’s all displayed in real-time, and booking is just a tap away. And, of course, everything is built with data privacy in mind.
To power the user-friendly interface we used LVGL, the “light and versatile visual library” perfect for building custom GUIs. We also leveraged Squareline Studio – because sometimes coding just feels like too much work – to easily design the display’s look and feel.
But why stop at meeting room booking? With this phygital system, you can integrate sensors to collect additional data like room temperature, humidity and lighting, automating systems to improve comfort and energy efficiency.
Get started today
Built on two of Arduino’s most advanced products, the Arduino GIGA and GIGA Display Shield, this solution opens endless possibilities for automation and customization in your office.
Alvik is cute, it’s smart, it’s fun… so what can it actually do? To answer this question, we decided to have fun and put the robot to the test with some of the most creative people we know – our own team! A dozen Arduino employees volunteered for a dedicated Make Tank session earlier this […]
Alvik is cute, it’s smart, it’s fun… so what can it actually do?
To answer this question, we decided to have fun and put the robot to the test with some of the most creative people we know – our own team! A dozen Arduino employees volunteered for a dedicated Make Tank session earlier this fall, and came up with a few great in-house projects for us to share – and you to try!
We were so happy with the creative and engaging ideas that we took them on the road for the Maker Faire Rome 2024: they were a hit and attracted many curious visitors to the Arduino booth.
Hello, Alvik!
This interactive project, created by Christian Sarnataro and Leonardo Cavagnis, brings to life Alvik’s friendly personality. By waving your hands in front of a Nicla Vision camera, you trigger a cheerful “big hands” gesture in response: it’s Alvik’s way of welcoming newcomers to robotics!
Why it’s great: The project highlights Alvik’s ease of use and intuitive interactivity, while demonstrating how advanced learners can tap into the robot’s AI capabilities to create meaningful, engaging robotic experiences.
Robo-Fight Club
Developed by Davide Neri and Alexander Entinger, this competitive game turns Alvik into a feisty battling robot. Participants control their Alvik to push opponents out of the arena, while trying special moves like “yellow-banana” for spins, “green-slime” to reverse controls, and “blue-ice” to freeze competitors for five seconds. Any robot stepping out of the arena automatically loses the match.
Why it’s great: Robo-Fight Club demonstrates how Alvik can be used for multiplayer, interactive gaming experiences while teaching users about programming logic and control systems.
Alvik Mini City
In this project by Giovanni Bruno, Julián Caro Linares, and Livia Luo, Alvik works tirelessly in a mini city, moving balls from one floor to another. The project showcases how robotics can assist in repetitive and potentially hazardous tasks, inspiring us to imagine practical applications for robotics in their daily lives.
Why it’s great: This project emphasizes how Alvik is more than just an educational robot – it’s a tool for exploring real-world use cases in automation and problem-solving.
Your turn!
Alvik is the perfect companion to learn coding and robotics because it’s easy to get started with, but powerful enough to support complex projects. With the option to program using block-based coding, in MicroPython or the Arduino language, everyone from beginners to advanced users can choose the environment that suits their needs best!
Inspired by these projects? Check out all of Alvik’s features and specs on this page, or go ahead and start your journey today! Don’t forget to share your creations with us: upload your projects to Project Hub or email [email protected] – we can’t wait to see what you build!
The Arduino UNO is legendary among makers, and with the release of the UNO R4 in 2023, the family gained a powerful new member. But with two incredible options, which UNO should you pick for your project? Here’s a breakdown of what makes each board shine, depending on your needs, skills, and goals. Why the […]
The Arduino UNO is legendary among makers, and with the release of the UNO R4 in 2023, the family gained a powerful new member. But with two incredible options, which UNO should you pick for your project? Here’s a breakdown of what makes each board shine, depending on your needs, skills, and goals.
Why the UNO Rev3 is still a go-to classic
The UNO Rev3 has been around for over a decade, earning its reputation as a solid, reliable board perfect for beginners. Simple, robust, and versatile, it’s the “base camp” of the Arduino ecosystem. Its 8-bit architecture makes it straightforward to understand exactly what’s happening in your code.
Applications and ideal uses
The UNO Rev3 is fantastic for projects like controlling LEDs, motors, and simple sensors – as well as any of the 15 projects included in our best-selling Arduino Starter Kit.
Its ability to handle a higher current directly from each pin makes it ideal for connecting power-hungry sensors or motors without needing extra components. It’s also compatible with an enormous number of sketches and libraries that have been built around it over the years.
One key advantage? The microcontroller on the UNO Rev3 can be removed, allowing you to use it independently – a feature that many seasoned users love.
The UNO R4 builds on everything makers love about the Rev3, adding features that bring it up to speed with the needs of today’s tech. Its 32-bit Arm® Cortex®-M4 guarantees significantly faster processing power and can handle more advanced projects. It comes in two versions: the UNO R4 Minima for essential functionality and the UNO R4 WiFi for Internet-connected projects.
The latter is the brains of the Plug and Make Kit: the easiest way to go from zero to tech hero, with step-by-step tutorials to create a custom weather station, a video game controller, a smart timer and so much more!
Advanced features for new possibilities
The UNO R4 packs in features that are groundbreaking for the UNO family:
12-bit DAC: Enables analog output for audio waveforms or other analog components without external circuitry.
CAN bus: Ideal for connecting multiple devices in robotics or automotive projects.
Wi-Fi® and Bluetooth® on the R4 WiFi model: Easily build IoT projects and connect to the Arduino Cloud to control your devices remotely.
Enhanced Diagnostics: The R4 WiFi includes an error-capturing mechanism that helps beginners by identifying issues in the code, a fantastic learning tool.
Applications and ideal uses
With increased memory and processing power, the UNO R4 is perfect for projects that require complex calculations or manage multiple processes. Think IoT, data sensing, automation systems, creative installations or scientific equipment where precise measurements and real-time adjustments are key.
What’s more, the UNO R4 has the capability to leverage AI – and our community has jumped at the chance of exploring whole new realms. One user built a gesture recognition system made of cardboard, another added smart detection to a pet door to always know if their cat was home or not, and another yet came up with a great tool to always know what song is playing. Not to mention the possibilities for advanced animationslike this one – inspired by Bad Apple – developed thanks to the LED matrix right on the UNO R4.
Is a 32-bit MCU always better than an 8-bit?
The short answer is, no. We believe the best solution is always determined by the requirements of the project at hand: bigger, faster, more powerful or more expensive is not always better.
8-bit microcontrollers process data in 8-bit chunks, which limits the size of numbers they can handle directly to values between 0 and 255 (or -127 and 128). This limitation makes them best suited for applications with minimal data processing needs, such as basic tasks like toggling LEDs or controlling simple sensors. However, they also tend to be more affordable and to consume less power, making hardware design less expensive, and have a simpler architecture, which translates to easier programming. So, if you are still learning the basics and need the most straightforward tool, or you are tackling a project with minimal requirements, an 8-bit MCU is not only all you need, but probably your best option.
On the other hand, if you need to work on much larger numbers and perform data-heavy calculations, 32-bit microcontrollers can handle advanced applications like image processing and real-time analytics. The difference is not just 4-fold going from 8 to 32: it’s a huge jump from 255 to 4,294,967,295! Almost by definition, any solution that requires this kind of performance will be more complex to design and program, require more memory, and consume more power, often affecting battery life. The upside, of course, is the incredible potential of what you can achieve!
Compatibility and transitioning from UNO Rev3 to UNO R4
If you already have experience with the UNO Rev3 and are considering the R4, but have concerns about compatibility, rest assured: they have the same form factor, pinout, and 5V operating voltage. This makes it easy to transfer accessories such as shields from one to the other.
On the software side, tutorials and projects are often compatible. We have even created a GitHub repository where you can check compatibility for libraries with the new R4 (and even help us update information or add new R4-friendly versions). This is part of the effort we share with our community to make sure that transitioning to the UNO R4 – if you choose to do so – is as seamless as possible.
Which Arduino UNO should I choose?
UNO Rev3
UNO R4
• Best for beginners or those working on foundational projects.
• Great for educational settings, where understanding core programming concepts and hardware interactions are the focus.
• Ideal if you need a reliable, budget-friendly, no-frills board with vast project resources available online.
• Perfect for advanced users or beginners looking to push boundaries with more complex projects.
• Best for IoT, data-intensive, or networked applications that require more processing power.
• A smart choice if you’re experimenting with new peripherals like CAN bus, DAC, or Wi-Fi/Bluetooth connectivity.
Choose your UNO and start creating!
Whether you choose the classic UNO Rev3 or the more recent UNO R4, you’re joining a global community of makers, educators, and inventors who love to create. Both boards offer incredible opportunities, each tailored to different stages and styles of making. Ready to dive into a new project? Buy your next UNO and discover limitless possibilities!
Arduino and Microchip are excited to open electronica – the “world’s leading trade fair and conference for electronics” – by introducing the Arduino UNO SPE Shield, a powerful ally to bring advanced connectivity to new and existing projects, with Single-Pair Ethernet (SPE) and RS485. SPE is a new Ethernet communication standard that enables power and […]
Arduino and Microchip are excited to open electronica – the “world’s leading trade fair and conference for electronics” – by introducing the Arduino UNO SPE Shield, a powerful ally to bring advanced connectivity to new and existing projects, with Single-Pair Ethernet (SPE) and RS485.
SPE is a new Ethernet communication standard that enables power and data to coexist on a single pair of wires, referred to as Power over Data Line (PoDL). This allows for faster data transfer and reduced wiring complexity and costs, leading to more streamlined and rapid deployment of integrated strategies for the automation of buildings, factories, and processes, in the context of the Internet of Things (IoT) and Industrial Internet of Things (IIoT).
By incorporating RS485 connectivity, the Arduino UNO SPE Shield becomes a versatile tool for upgrading RS485 legacy systems or integrating modern technologies with current infrastructures, creating a seamless bridge between the old and the new.
As a valuable new addition to the Arduino ecosystem, the Arduino UNO SPE Shield offers plug-and-play compatibility with Arduino UNO R4 – catering to a broad spectrum of innovators, from DIY enthusiasts to engineers developing cutting-edge solutions for industrial applications.
In recognition of this joint effort, Martin Miller, Director of Automotive Information Systems at Microchip remarked: “Our collaborationwith Arduino in launching the new SPE Shield aims to empower the maker and engineering communities by providing them with advanced tools to drive new breakthroughs. This solution represents our commitment to developing and delivering flexible, connected and scalable solutions for the future.”
Indeed, the partnership has allowed for a product that delivers both cutting-edge, reliable technology as well as versatility and a user-friendly experience.
Fabio Violante, CEO of Arduino, commented: “The Arduino UNO SPE Shield represents a pivotal step in accelerating the adoption of 10BASE-T1S technology across industry and maker communities alike. By bringing single-pair Ethernet to our globally trusted platform, we’re making this game-changing standard accessible to millions of innovators worldwide. What sets our implementation apart is our unique addition of Power over Data Lines capabilities – an industry-first feature that extends beyond the standard specifications to unlock entirely new possibilities for powered, single-cable solutions. This powerful combination of standardized communication and innovative power delivery empowers developers to create more elegant, cost-effective connected systems that bridge today’s industrial requirements with tomorrow’s possibilities. Whether you’re retrofitting legacy equipment or prototyping next-generation IoT devices, the UNO SPE Shield delivers the essential building blocks for modern industrial communication in our signature easy-to-use Arduino format.”
Key benefits of the Arduino UNO SPE Shield
Fast and reliable data transfer with Single-Pair Ethernet.
Reduced wiring complexity and lower project costs.
Versatile use across industries from smart factories to energy monitoring.
Seamless integration with the widest range of technologies, ensuring a quick start with minimal setup.
Plug-and-play compatibility with Arduino’s major maker platform for makers at all levels.
Open-source support with a dedicated Arduino library to streamline programming and development.
Revolutionizing connectivity across industries
The Arduino UNO SPE Shield enables enhanced innovation across a wide array of fields, solving real-world challenges from smart buildings to prototyping IoT devices.
For instance, with the Arduino UNO SPE Shield interconnected building management solutions can easily combine smart lighting, HVAC, and security devices with energy monitoring systems – all integrated via a central control system powered by SPE and RS485.
In general, the new SPE standard is considered a game changer for the connection of field devices and sensors. For example, in smart-grid monitoring the SPE Shield provides seamless connectivity between energy meters, solar inverters, and battery storage systems, delivering real-time data to the cloud.
In factory automation, adopting SPE can reduce wiring costs, node costs, and power consumption, while enabling data communications via a single pair of wires. Being able to effortlessly retrofit legacy RS485 equipment with this technology only adds to the benefits of the Arduino UNO SPE Shield.
In the automotive industry, combining SPE and RS485 allows for solutions that bridge advanced systems with legacy components, enabling comprehensive monitoring of engine health and fuel efficiency in connected vehicles.
Last but not least, the SPE Shield’s unique combination of ultra-fast data transfer, real-time connectivity and seamless integration with legacy components facilitates quick testing and refinement of prototypes, accelerating the development of new ideas.
Connect to your next innovation, withArduino UNO SPE Shield. Sign up for the waiting list to be the first to know when it’s available for purchase!
We’re thrilled to announce that Arduino Education has been shortlisted for the Bett Awards 2025, this time in the AV, VR/AR, Robotics, or Digital Device category with our Alvik robot! This recognition highlights our dedication to innovation, inclusivity, and the advancement of practical STEM education. The Bett Awards celebrate leading-edge technology in education, with entries […]
We’re thrilled to announce that Arduino Education has been shortlisted for the Bett Awards 2025, this time in the AV, VR/AR, Robotics, or Digital Device category with our Alvik robot! This recognition highlights our dedication to innovation, inclusivity, and the advancement of practical STEM education.
The Bett Awards celebrate leading-edge technology in education, with entries evaluated on key criteria such as innovation, curriculum suitability, online safety, research evidence, customer support and more.
About the Alvik robot
Alvik is an adaptable, lifelong learning robot that supports educators and students as they transition from block-based programming to text-based coding using MicroPython and Arduino language. It enables them to explore robotics and tackle real-life challenges with comprehensive learning content. However, Alvik isn’t just designed to teach programming and robotics; it can also enhance students’ understanding of topics like mathematics and astronomy, along with other engaging projects. Alvik’s curriculum-aligned course makes it an ideal fit for today’s classrooms, empowering students with hands-on skills and a strong foundation in STEAM.
But what truly sets Alvik apart from other educational robots is its limitless potential for customization. Students and teachers can easily add external sensors using the I2C Grove and Qwiic plug-and-play connectors, eliminating the need for soldering or complex wiring. Additionally, the LEGO® Technic and M3 screw connectors encourage hands-on creativity, allowing users to build custom components and further expand Alvik’s capabilities.
We’re honored to be recognized once again, and we can’t wait to attend Bett in just a couple of months. The winners will be announced at the Bett Awards 2025 Ceremony on January 22nd at The Brewery, London. We look forward to seeing you there!
Good designers prioritize the user experience — particularly the experience of users with disabilities that affect their perception and fine motor skills. A young person without disabilities, for example, may feel that jars are easy to open, while an elderly person with reduced hand strength may have the complete opposite experience. To help designers better […]
Good designers prioritize the user experience — particularly the experience of users with disabilities that affect their perception and fine motor skills. A young person without disabilities, for example, may feel that jars are easy to open, while an elderly person with reduced hand strength may have the complete opposite experience. To help designers better understand the experience of people living with disabilities related to hand dexterity, a team of graduate students from Keio University and the University of Maryland developed DexteriSync.
DexteriSync is an exoskeleton-like device worn on the hand. But unlike most exoskeletons, DexteriSync reduces the user’s ability instead of expanding it. It does so via thermal manipulation. If you’ve ever had numb hands following a snowball fight, you know how much the cold can affect your dexterity. In fact, skin temperature is one of the biggest factors related to hand and finger dexterity. By controlling the user’s skin temperature, DexteriSync is able to induce a reduction in dexterity and that could be useful to designers that want to make their products accessible to those living with disabilities.
DexteriSync is able to cool the wearer’s skin by pumping cold water through tubes attached to the 3D-printed exoskeleton frame. Copper contacts on the tubes help to make the thermal transfer more efficient. Peltier coolers remove heat from the pumped water, with an Arduino UNO Rev3 board controlling that process and monitoring the water temperature with a K-type thermocouple paired with a MAX6675 amplifier.
The team performed two user studies to evaluate DexteriSync. The first was intended to test the dexterity of users. The goal of the second was to determine if DexteriSync could affect user thermal perception. Both studies found that DexteriSync did have a noticeable effect.
Wouldn’t it be great if, while playing a virtual reality game, you could feel the heat of a fire on your arm? Or the cold of chilly water? Engineers around the world have been trying to make that happen, but there is a big problem: temperature changes are slow. The immersive effect diminishes when the […]
Wouldn’t it be great if, while playing a virtual reality game, you could feel the heat of a fire on your arm? Or the cold of chilly water? Engineers around the world have been trying to make that happen, but there is a big problem: temperature changes are slow. The immersive effect diminishes when the thermal feedback lags behind the virtual cause. That’s why a team from South Korea’s Gwangju Institute of Science and Technology turned to motors to dramatically speed up the process.
The Flip-Pelt wearable device relies on Peltier elements to create heating and cooling effects, which is a common strategy for thermal feedback. Peltier elements use electricity to produce thermal transfer, heating one side of the element while simultaneously cooling the other side. By placing a Peltier element against the skin, it is possible to create a cooling or heating sensation on demand.
But it takes a long time to reverse the thermal transfer — changing a side of the Peltier element from hot to cold is too slow to be useful for VR thermal feedback. So, the Flip-Pelt prototype doesn’t even bother. Instead, it keeps the Peltier elements going in just one direction and physically swaps the side of the elements that touch the user’s skin.
The prototype Flip-Pelt device contains eight Peltier elements arranged in two rows along the inside of the user’s forearm. Eight servo motors, controlled by an Arduino Nano 33 IoT board, can flip the elements from the cool side to the hot side in response to events in the VR world. The Arduino also controls the Peltier elements themselves through H-bridges, so it can adjust the power going to each.
While this is relatively complex, it does create almost instant changes in perceived temperature.
and M3 screw connectors encourage hands-on creativity, allowing users to build custom components and further expand Alvik’s capabilities.
